لتحميل التحديثات أدخل هنا
.
للإشتراك سنة أو سنتين أو 3 سنوات
تسجل في الموقع الجديد وأعطي الإيميل
الخاص بلك للوكيل أو صاحب البرنامج
تنبيه : أي شخص إشترك قبل 01..01..2026
عليه أن يحافض على نسخة من البرنامج
وكذلك على تفعيله كما هو مذكور في الصور المرفقة
وإذا لم يقم بذلك لا يمكننا مساعدته
ويلزمه الإشتراك في النظام السنوي الذي بدأ بعد 01..01..2026
لأن العرض والنظام القديم إنتهى
وأصبح النظام بالإيميل مثل البرنامج الأجنبية
Attention : Anyone who subscribed before January 1, 2026
, must keep a copy of the program and activate it as shown
in the attached images. If they fail to do so, we cannot assist them
, and they will need to subscribe to the annual plan that
began after January 1, 2026, because the old offer and system have ended,
and the system is now email-based, similar to foreign programs.
: If the screen remains blank in Proteus, double-check that the pull-up resistors (typically
Proteus allows you to simulate the JHD-2x16-I2C using:
The easiest way to drive this display in simulation is using the Arduino IDE environment with the library. Arduino Source Code
In the world of embedded systems, the 16x2 character LCD is a staple for displaying diagnostic data, user menus, and sensor readings. The module (often simply called the I2C LCD) has revolutionized how we interface with these displays by reducing the required I/O pins from 6 to just 2.
: I2C lines require pull-up resistors (typically 4.7k or 10k ohms) connected to VCC to function correctly in the simulation. 3. Finding the I2C Address
Which are you using to generate your hex file?
ATMEGA328P or ARDUINO UNO (or your preferred MCU like PIC or 8051) LM016L (The standard 16x2 LCD display) PCF8574 (The I2C I/O Expander) PULLUP (Resistors for the I2C bus) Step 2: Wiring the PCF8574 to the 16x2 LCD
Ensure the I2C address in the simulation matches the code (default is usually 0x20 in many simulated libraries). 4. Coding and Simulation Steps
Open Proteus Isis Schematic Capture, press on your keyboard to open the Pick Devices window, and search for the following keywords to add them to your workspace:
To get the JHD-2X16-I2C displaying text correctly in your simulation: Switch Libraries : Many users find success by switching to the DF Robot LCD Point H library instead of the standard LiquidCrystal one. Verify the Address I2C Scanner Sketch
Right-click the JHD-2x16-I2C in Proteus and edit its properties. Look for I2C Address . Set it to 0x27 (most common). If your code uses 0x3F , change it here.
: If the screen remains blank in Proteus, double-check that the pull-up resistors (typically
Proteus allows you to simulate the JHD-2x16-I2C using:
The easiest way to drive this display in simulation is using the Arduino IDE environment with the library. Arduino Source Code jhd-2x16-i2c proteus
In the world of embedded systems, the 16x2 character LCD is a staple for displaying diagnostic data, user menus, and sensor readings. The module (often simply called the I2C LCD) has revolutionized how we interface with these displays by reducing the required I/O pins from 6 to just 2.
: I2C lines require pull-up resistors (typically 4.7k or 10k ohms) connected to VCC to function correctly in the simulation. 3. Finding the I2C Address : If the screen remains blank in Proteus,
Which are you using to generate your hex file?
ATMEGA328P or ARDUINO UNO (or your preferred MCU like PIC or 8051) LM016L (The standard 16x2 LCD display) PCF8574 (The I2C I/O Expander) PULLUP (Resistors for the I2C bus) Step 2: Wiring the PCF8574 to the 16x2 LCD : I2C lines require pull-up resistors (typically 4
Ensure the I2C address in the simulation matches the code (default is usually 0x20 in many simulated libraries). 4. Coding and Simulation Steps
Open Proteus Isis Schematic Capture, press on your keyboard to open the Pick Devices window, and search for the following keywords to add them to your workspace:
To get the JHD-2X16-I2C displaying text correctly in your simulation: Switch Libraries : Many users find success by switching to the DF Robot LCD Point H library instead of the standard LiquidCrystal one. Verify the Address I2C Scanner Sketch
Right-click the JHD-2x16-I2C in Proteus and edit its properties. Look for I2C Address . Set it to 0x27 (most common). If your code uses 0x3F , change it here.
Calculator News Enable Adb
By Girgis + ALi Hassani +Emad Hafeedk
Enable Adb By Calculator
1 - Open Calculator
2 - Entre the code (+30012012732+)
3 - Entre the code +#0808#
4 - Chose MTP + ADB
Enable Adb By Call
1 - backup all app from samsung cloud
2 - install s9 Luancher or Go Launcher
3 - Entre the code +#0808#
4 - Chose MTP + ADB
يستعمل الإختصار أخي الكريم وأختي الكريمة للولوج إلى التطبيق مباشرة من المتصفح
دون الحاجة إلى تنصيب اللانشر من جالاكسي ستور بشرط أن تقوم بتنصيب التطبيق
من هنا وإرجاعه للهاتف الٱخر من حساب سامسونغ
The abbreviation my dear brother and my dear sister is used to
access the application directly from the browser Without the need
to install the launcher from the Galaxy Store, provided that you install the application
From here and return it to the other phone from the Samsung account
*************************************
.
*************************************
*************************************
*************************************
Go Launcher
*************************************
*************************************
*************************************
-------------------------------------------------------